/3425$4*0/ )&&4
0'
9$0 -&$420/*$3 02102"4*0/ "22*3#52( -- /4&2/"4*0/"- *()43 &3&26&% -0(0 "/% 9$0 -&$420/*$3 "2& 42"%&."2,3 2"%&."2, 4)&2 120%5$43 -0(03 "/% $0.1"/9 /".&3 53&% "2& 4)& 1201&249 0' 4)&*2 2&31&$4*6& 07/&23
)*3 $0/420--&% %0$5.&/4 *3 35#+&$4 40 $)"/(& 02 -"4&34 2&6*3*0/ "/% &(*0/"- 5340.&2 &26*$& 6*3*4 052 7*4& "4 )))'+ $ ! '%$# & $"
&6 *'% ' $# $$! figure 1 %+534.&/4 "1 "/%-& 53) */ 12*/(0"%&% *1 extraction tool 15832371 (shown in figure 1) is designed to extract individual pin (post) contacts from hmzd header connectors. the connectors can be removed from the printed circuit (pc) board using hmzd header removal tools 15832201 and 15832341 (refer to 4088645).
read these instructions before using the extraction tool. reasons for reissue of this instruction sheet are provided in section 6, revision summary. the extraction tool consists of a handle, adjustment cap, springloaded tip, and push pin. see figure 1. the adjustment cap, located on one end of the handle, can be set to allow the push pin to recess or extend out of the springloaded tip while extracting the pin contact. the push pin pushes on the pin contact and ejects it from the pc board and connector.
# $#' ' *' # +$# $% (% 1. turn the adjustment cap clockwise until the push pin is extended (approximately 0.51 [.020]) beyond the end of the springloaded tip. refer to figure 2. figure 2 53) */ 84&/%&% ! 11208 12*/(0"%&% *1 "/%-& 2. with the push pin extended, locate the appropriate pc board hole (in the back side of the pc board) of the pin contact to be extracted, and place the push pin into the hole. refer to figure 3. figure 3 84&/%&% 53) */ -*(/&% 7*4) */ 0/4"$4 0-& "$, *%& 0' 0"2% 0//&$402 3. holding the tool perpendicular to the pc board, apply pressure to the tool until the pin contact is ejected from the pc board and connector.
,*( *#&% &&$
!
" #% &%* * ,*!% ! !-&% & ( +(" ! 1. turn the adjustment cap counterclockwise until the push pin is retracted (recessed) into the end of the springloaded tip. refer to figure 4.
figure 4
2. with the push pin retracted (recessed), locate the tip of the pin contact (from the back side of the pc board) to be extracted. 3. place the springloaded tip over the tip of the pin contact. see figure 5. 4. holding the tool perpendicular to the pc board, apply pressure to the tool until the pin contact (post) is ejected from the pc board and connector.
figure 5
!
it is recommended that the tool be inspected immediately upon its arrival to ensure that it has not been damaged during shipment. #$- #%*!% % ! it is recommended that each operator be made aware of, and responsible for, the following steps of daily maintenance: 1. remove dust, moisture, and other contaminants with a clean, soft brush, or lintfree cloth. do not use objects that could damage the tool or any of its components. 2. when the tool is not in use, store it in a clean, dry area. !(#& # %)'! *#&% regular inspections should be performed by quality control personnel. a record of scheduled inspections should remain with the tool or be supplied to supervisory personnel responsible for the tool. the inspection frequency should be based on the amount of use, working conditions, operator training and skill, and established company standards.
order extraction tools through your representative, or call 18005265142, or send a facsimile of your purchase order to 7179867605, or write to: customer service (038035) tyco electronics corporation po box 3608 harrisburg pa 171053608 for customer repair service, call 18005265136.
revisions to this instruction sheet include: updated document to corporate requirements changed aand contacto to aand connectoro in step 3 of paragraph 3.1 and step 4 of paragraph 3.2
|
